XTP 4K Transmitter and Receiver Boards With RS-232 and IR Insertion

Video XTP CP 4i, XTP CP 4o

   Gain 

Unity

   Resolution range 

Up to 1920x1200*, 2K, or 1080p @ 60 Hz
*reduced blanking

   Signal type 

Single-link HDMI (or DVI-D*)

      Digital video 

RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI [if using an optional adapter] and HDMI standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz) or 2K

      EDID and DDC 

Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards.  EDID and DDC signals are actively buffered.

      HDCP 

Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI standards

      HPD 

Supports hot plug detection (HPD) of display as a pass-through signal.

   Maximum pixel clock 

165 MHz

   Standards 

DVI 1.0, HDMI 1.3, HDCP 1.1

   Switching speed 

200 ns (max.)

   Video format 

HDMI and DVI

   Audio format 

Analog stereo, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master Audio, up to 8 ch PCM, Dolby Atmos

Shielded twisted pair interconnection

   Number/signal type 

4 sets of proprietary signals

   Connectors 

4 female RJ-45 per board

   Signal termination standards 

TIA/EIA T568B

   Input cable length 

Up to 330" (100 m) using shielded twisted pair or XTP DTP 24 cable

      Cable requirements 

Solid conductor, 24 AWG or better

      Cable recommendations 

400 MHz bandwidth, STP (shielded twisted pair)

Control/remote external device (pass-through)

   Serial control pass-through ports 

4 RS-232, via 3.5 mm, 5-pole captive screw connectors (shared with IR ports)

   Baud rates 

300 to 115200 baud

   Protocol 

5 to 8 data bits
1 or 2 stop bits
no parity (default), even or odd parity
flow control Xon, Xoff, and none

   Serial control pin configuration 

1 = Tx, 2 = Rx, 3 = GND

   Ethernet pass-through ports 

4 female RJ-45

   Ethernet data rate 

10/100Base-T, half/full duplex with autodetect

   IR control ports 

4, via 3.5 mm, 5-pole captive screw connectors (shared with RS-232 ports)

   IR control pin configuration 

3 = GND, 4 = IR Tx, 5 = IR Rx

General

   Power 

Supplied by XTP CrossPoint or XTP II CrossPoint enclosure

   Power consumption 

      XTP CP 4i 

         PoE 

79 watts (XTP II CrossPoint 3200)
95 watts (XTP II CrossPoint 6400)

         No PoE 

35 watts

      XTP CP 4o 

         PoE 

75 watts (XTP II CrossPoint 3200)
90 watts (XTP II CrossPoint 6400)

         No PoE 

21 watts

   Product weight 

2.0 lbs (0.9 kg)

   Regulatory compliance 

      Environmental 

Complies with the appropriate requirements of RoHS, WEEE.

   Product warranty 

3 years parts and labor