White UHD- 4K HDMI-USB Over IP PoE Wall Plate Receiver

Get a Price/Quote

Product Details:

Click to View more
Share Your Product:

Request to Call Back Send Inquiry

Product Description

Key Features

Transmits HDMI plus control and analog audio up to 230 feet (70 meters) over a shielded CATx cable
Supports computer and video resolutions up to 4K
Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance
Compatible with CATx shielded twisted pair cable
Accepts additional analog stereo audio signals
JITC Certified

specification

Frame rate1

24, 25, 30, 50, or 60 fps

Chroma sampling1

4:4:4, 4:2:2, or 4:2:0

Color bit depth1

8 bits per color

Signal Type

HDMI 1.4, HDCP 2.3

Max. video data rate

10.2 Gbps (3.4 Gbps per color)

NOTE	1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.

Video

Maximum data rate

10.2 Gbps (3.4 Gbps per color)

Maximum pixel clock

300 MHz

Resolution range

Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(*Reduced blanking)

Color bit depth

8, 10, or 12 bits subject to the maximum data rate limit

Formats

RGB and YCbCr digital video

Standards

DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E

Video input

Number/signal type

1 single link HDMI (or DVI-D*) input

Connectors

1 female HDMI type A

NOTE	*Appropriate HDMI to DVI-D cables or adapters are required for HDMI signal input/output.

Interconnection between transmitter and receiver

Connectors

1 female RJ-45 per unit for 1 cable connecting the transmitter and receiver

Termination standards

TIA/EIA T568B

DTP signal

Signal transmission distance

1080p @ 60 Hz

Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable

2560x1600 @ 60 Hz

Up to 130' (40 m) using STP cable or XTP DTP 24 cable

4K/UHD @ 30 and 60 Hz

Up to 130' (40 m) using STP cable or XTP DTP 24 cable

Cable requirements

Solid conductor, 24 AWG or better

Cable recommendations

400 MHz bandwidth STP cable

NOTE	Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.

NOTE	Output mode signaling: DTP: HDMI with embedded audio, analog audio, RS-232 and IR, and remote power HDBaseT: HDMI with embedded audio plus RS-232 and IR

Audio

Gain

Unbalanced output: 0 dB; balanced output: +6 dB

Frequency response

20 Hz to 20 kHz, 0.5 dB

THD + Noise

0.03% @ 20 Hz to 20 kHz at maximum output

S/N

>90 dB at maximum output (15 dBu), balanced (unweighted)

Stereo channel separation

>80 dB @ 1 kHz to 20 kHz

Audio input

Number/signal type

1 stereo (2 channel), unbalanced

NOTE	Analog audio is not embedded onto the digital video signal. Analog audio and digital embedded audio are transmitted simultaneously and output on the receiver on two different connectors.

Connectors

(1) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (ground)

Impedance

>10k ohms, DC coupled

Nominal level

-10 dBV (316 mVrms)

Maximum level

+7 dBV, unbalanced

NOTE	0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu

Communications external device (RS-232/IR over TP)

Serial control port

RS-232 via (1) 3.5 mm, 5 pole captive screw connector<BR>(connector is shared with IR control port)

NOTE

Protocol is mirrored between the connected DTP 230 or DTP 330 endpoints and the "Over TP" ports on the
DTP T HWP 231 D. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints.

Baud rates

Up to 115200 baud

Protocol

Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none

Serial control pin configuration

Captive screw connectors: 1 = Tx, 2 = Rx, 3 = Gnd

IR control port

(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz

IR control pin configuration

3 = Gnd, 4 = IR Tx, 5 = IR Rx

General

Power supply

External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts

Power consumption

Device

3.0 watts

Device and power supply

3.9 watts

Remote power budget

12 watts

NOTE	Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.

Ambient temperature/humidity

Storage: -40 to +158 F (-40 to +70 C) / 10% to 90%, noncondensing
Operating: +32 to +122 F (0 to +50 C) / 10% to 90%, noncondensing

Cooling

Convection, no vents

Thermal dissipation

Device

10.0 BTU/hr

Device and power supply

13.3 BTU/hr

Mounting

Furniture or wall mount

Yes, with a 1-gang wall box or mud ring

Enclosure type

Metal

Enclosure dimensions

Faceplate

2.6" H x 1.3" W x 0.3" D
(6.6 cm H x 3.3 cm W x 0.6 cm D)

Device

2.8" H x 1.7" W x 1.9" D
(7.1 cm H x 4.3 cm W x 4.8 cm D)

NOTE	Overall height is 4.2" (10.7 cm), including mounting tabs. Mounting holes are 3.2" (8.2 cm) apart on center. Depth excludes connectors. Fits the opening in a 1 gang decorator wallplate).